Home plumbing is a modern convenience! Indoor plumbing means you do not have to live by a creek or use an outhouse. However, keeping this luxury functioning – where and how you want – without drowning everyone in your home can be an interesting challenge! Read on for some advice on controlling the flow of water in your home.

You need to winter-proof your house. You have to make sure you switch of the master circuit breaker or the shut-off valve before you leave your house. Since one small hole or congested water can quickly freeze and cause pipes to break and expand, you need to drain and open all outdoor and household water lines.

If you loved this article and you would like to obtain more info regarding Precision Handyman Boston nicely visit our web-site. To avoid clogs, pay attention to what you flush. Sanitary napkins, thick toilet paper and baby wipes should never be flushed. These items can expand and cause a clog, or get caught on a pipe. Instead, dispose of them in a sanitary way that does not involve flushing them down the toilet.

Use your garbage disposal with the cold water running so that you can preserve the blades of the disposal. Using hot water makes grease more liquid and can cause problems, including clogs. Make sure to clean blades by putting in a little dish detergent and run cold water at the same time.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

There are many ways to unclog a drain. You can try plunging it at first. If that doesn’t work try using a chemical agent from the store. Before you go and spend money at the store though, if you have baking soda and some vinegar handy, you can mix those together and pour them in the drain and try to plunge that but if all else fails they have stronger remedies at your local hardware store.

During the winter, preventing frozen pipes when you live in a small dwelling can be something good to know. Frozen pipes will not only stop your flow of water but can crack and damage pipes. By running a little water out of every faucet during the coldest parts of the day, you can avoid this.

If you have problems with a slow drain, there are easier things you can do other than removing the pipes to clean it. There are certain tools made just for this purpose that you insert into the drain to loosen the clog so it washes away or grab it and remove it completely.

Sometimes kitchen sinks can be clogged up due to a slow accumulation of solidified grease. One quick fix for this is to try pouring very hot grease down the sink, which will liquefy the grease clogging the drain and carry it down. Water won’t work, because grease will not dissolve in water.

Look online for reviews of the plumbing contractor you are thinking of hiring. If people are not satisfied with the work that the plumber preforms, many times they will go on the internet and post negative reviews. If they are happy with the plumber they will also post positive reviews.

Frozen pipes can lead to many problems, most of them expensive to fix. So you want to avoid that at all costs. To avoid frozen pipes, make sure the temperature in your home never drops below 55 degrees. Look for any air leaks around your pipes and make sure they’re sealed up.

Use a product like BioBen if you are planning to leave your system shut off for a few weeks. Water will still remain in the pipes and could start smelling because it is not moving. This type of product will keep the water from stagnating and from smelling too bad.

If your toilet is constantly developing moisture on the outside, you may want to consider turning up the heat in your bathroom. The biggest cause of “sweaty” toilets is cool and moist air. Believe it or not, this moisture could actually cause damage to your toilet, so it is crucial that you fix the problem.

A normal pipe snake can clean out your washing machine’s drain stack if it backs up. Lint and small debris in your washing machine can accumulate and create a clogged drain.

Try to update your internal toilet components from time to time. If you have to hold down the handle for a long time to flush your toilet, you may need to replace a worn piece. This improvement will help to save a lot of money on your water bill during the year.

Use chemicals that are designed to clean your drain with caution. These chemicals can open your drain but they also may hurt you if you get them on your skin. If you must use such chemicals, be sure to wear long sleeves and gloves.

To prevent the most common kitchen sink clogs, avoid putting any sort of solid foods down your drain. Many foods, such as eggs and vegetable and fruit waste actually harden with exposure to cold water and over time can form clogs that are next to impossible to remove without professional help.

Be sure to have a running toilet fixed as soon as you can. Having a running toilet uses more water, which raises your water bill. To fix it yourself, you just have to find out what the problem is and buy the supplies you need. If you can’t fix it yourself, call a plumber.

No one wants to have problems with their plumbing, but with the right knowledge and some hard work, these problems can be remedied. With knowledge, you can deal with some plumbing problems without needing to hire a plumber. Do a favor for yourself and listen to these tips above to fix your plumbing issues.


Posted by in Uncategorized Tags: